Digital Multimeter with Case, DC AC Voltmeter, Ohm Volt Amp Test Meter and Continuity Test Diode Voltage Tester for Household Outlet, Automotive Battery Test (Anti-Burn with Double Fuses)

Product Description The Fluke 1587 digital insulation multimeter (also known as a multitester) is a true RMS, auto- and manual-ranging meter insulation resistance, current, voltage, and resistance for testing line insulation on motors, generators, cables, and switch gear. The insulation test voltages of 50, 100, 250, 500 and 1000V measure resistance from 0.01 megohms to 2 gigohms. The meter also measures capacitance, frequency, and resistance. Temperature is measured using a K-type thermocouple (included). A diode test detects correct functioning of a circuit's diodes. A low-pass filter provides accurate AC voltage and AC frequency measurements on inverters and variable-frequency motor drives by blocking unwanted voltages. Live circuit detection increases user safety by preventing insulation tests when voltages exceed 30 volts, and auto-discharge of capacitive voltage increases user protection. An audible continuity sensor confirms a circuit conducts electricity. The LCD is backlit for readability in low light. A Hold function freezes the reading on the display. An alarm sounds when the test leads are connected to the wrong jack for the measurement being taken. The unit automatically turns off after 20 minutes of nonuse to conserve battery life or can be disabled for extended readings, and a low-battery indicator signals when the meter's batteries need to be replaced. The meter included a set of detachable test leads, a remote probe, alligator clips, a hard case, and instructions. This true RMS (root mean square) meter provides accurate readings when measuring linear loads, such as standard induction motors and incandescent lights, where the current or voltage has an undistorted waveform, or nonlinear loads, such as electronic devices or motors, where the current or voltage has a distorted waveform. When turned on, the meter is in auto-ranging mode and automatically selects the correct operating range for the property being measured. It can be switched to manual-ranging mode, which allows the operator to choose the appropriate operating range. The display has a 6,000-count resolution, meaning it can display up to 5,999 units (3-3/4 digits) before the operating range needs to be changed. It meets International Electrotechnical Commission (IEC) safety standard 61010 and is certified Category III installations up to 1000V, which covers items used with enclosed building circuit installations (such as service panel parts, branch circuits, and fixed installations that are connected directly to a building's AC power supply), Category IV installations up to 600V, which covers equipment at the origin of the installation (such as electricity meters and primary over-current protection equipment), and Pollution Degree 2 for indoor use. Specifications Insulation test voltages50V, 100V, 250V, 500V, 1000VInsulation measurement range0.01 megaohms to 2 gigohmsMaximum AC and DC voltage measurement1000VMaximum AC and DC current measured60 milliampResistance0.1 ohms to 50 megaohmsMaximum frequency99.99kHzTemperature probe and rangeK-type thermocouple -40 to +537 degrees C/-40 to +998 degrees FMaximum capacitance9999 microfaradsPower supply4 AA batteries (NEDA 15A or IEC LR6)Safety ratingsIngress Protection (IP)-40; European Conformity (CE); Underwriter's Laboratory (UL) 61010-1; ANSI/ISA S82.01-2004; Canadian Standards Association (CAN/CSA) C22.2 No. 1010.1:2004; International Electrotechnical Commission (IEC) safety standards IEC61557-1; IEC61557-2; IEC 61010-1:1002, IEC 61010.1-04, and IEC/EN 61010-1, 2nd edition for Category III installations up to 1000V and Category IV installations up to 600V, and Pollution Degree 2Weight1.2lb./550gDimensions1.97 x 3.94 x 8.00 inches/5.0 x 10.0 x 20.3cm (H x W x D) H is height, the vertical distance from the lowest to highest point; W is width, the horizontal distance from left to right; D is depth, the horizontal distance from front to back. Multimeters are electrical test meters that measure multiple properties of an electrical circuit, such as current, voltage, resistance, capacitance, and continuity. Available in handheld or benchtop models, multimeters diagnose electrical problems in electrical equipment, wiring, and power supplies. A variety of probes, clamps, and leads can be used to connect the meter to a circuit or device. Multimeters display information either in analog or digital form. Factors that influence meter choice include the electrical properties to be measured, the anticipated range of results, and the desired level of protection against transient voltage. Safety ratings are based on International Electrotechnical Commission (IEC) standards for low-voltage test equipment. IEC 61010 delineates four overvoltage installation categories. In general, a meter with a category IV rating will provide more protection against transient voltages than a meter with a lower category rating. Fluke Corporation manufactures electrical testing tools and software for industrial and commercial applications. The company, founded in 1948, is headquartered in Everett, WA. What's in the Box? Fluke 1587 digital insulation multimeter K-type thermocouple Remote probe Test leads (red and black) Alligator clips (red and black) Hard case Instructions From the Manufacturer The Fluke 1587 insulation multimeter combines a digital 1 Kv insulation tester and full featured true-rms digital multimeter in a single compact handheld unit. It provides maximum versatility for both troubleshooting and preventive maintenance. Like other tools from Fluke, the 1587 is rugged, reliable and easy to use. Whether you work on motors, generators, cables, or switch gear, this Insulation Multimeter is ideally suited to help you with your task. It includes a remote probe, test leads, alligator clips, K-type thermocouple, four AA alkaline batteries, quick reference guide, CD Rom with manual all included in a hard case, that allows you to bring everything you need for the job.

• Customer Service: Xiangtat provides a lifetime after sale service and technical support. This digital multimeter is included with 2 AAA batteries (pre-installed), comes with a carrying case and 2 decent cable leads.
• Multi-Function: This multimeter can test AC/DC Voltage, DC current (Can not for AC current), Resistance, Continuity, Diode Measurement.
• Sensitive Test: Please make sure the rotary switch is located at the right test range. Data hold function, backlight function helps you test clearly and quickly in a dim place.
• Safety Operation: IEC Rated CAT III 600V, CE and RoHS certified. Anti-Burn with double fuses. This multimeter has overload protection on all ranges.
• Widely Used: The Digital Multimeter is designed to be safe and accurate, and suitable for electrician test, household use, automotive, industrial electrical problems.